This README belongs to release 3.7 or newer of the SoundBlaster Pro (Matsushita, Kotobuki, Panasonic, CreativeLabs, Longshine and TEAC) CD-ROM driver for Linux. The driver is able to drive the whole family of "traditional" IDE-style (that is NOT the new "Enhanced IDE" or "ATAPI" drive standard) Matsushita, Kotobuki, Panasonic drives, sometimes labelled as "CreativeLabs". The well-known drives are CR-521, CR-522, CR-523, CR-562, CR-563. The Longshine LCS-7260 is a double-speed drive which uses the "old" Matsushita command set. It is supported now - with help by Serge Robyns. There exists an "IBM External ISA CD-ROM Drive" which in fact is a CR-563 with a special controller board. This drive is supported (the interface is of the "LaserMate" type), and it is possibly the best buy today (cheaper than an internal drive, and you can use it as an internal, too - f.e. plug it into a soundcard). CreativeLabs has a new drive "CD-200". Support is under construction. Drive detection and playing audio should already work. I need qualified feedback about the bugs within the data functions or a drive (I never saw a CD200). The quad-speed TEAC CD-55A drive is supported. The routines may still be a little bit buggy, but the data rate already reaches 500 kB/sec if you set SBP_BUFFER_FRAMES to 64. The drive is able to deliver 600 kB/sec, so this has to get a point of work. This driver is NOT for Mitsumi or Sony or Aztech or Philips or XXX drives, and this driver is in no way usable for any new IDE ATAPI drive. This driver will work with the soundcard interfaces (SB Pro, SB 16, Galaxy, SoundFX, ...) and/or with the "no-sound" cards (Panasonic CI-101P, LaserMate, WDH-7001C, Longshine LCS-6853, older Aztech cards, ...). It should work too now with the "configurable" interface "Sequoia S-1000", which is found on the Spea Media FX sound card. I still need feedback about this, or such a card. Anyways, the procedure "boot DOS and wait until CONFIG.SYS is done, then use CTL-ALT-DEL to boot Linux" should make it work. The interface type has to get configured in /usr/include/linux/sbpcd.h, because the behavior of some sound card interfaces is different. With some TEAC drives I have seen interface cards which seem to lack the "drive select" lines; always drive 0 gets addressed. To avoid "mirror drives" with such interface cards, set MAX_DRIVES to 1 and jumper your drive to ID 0. The driver respects all known drive firmware releases - my old drive is a 2.11, but it should work with CR-52x drives <2.01 ... >3.00 and with CR-56x drives <0.75 .. 5.00. Up to 4 drives per interface card, and up to 4 interface cards are supported. All supported drive families can be mixed, but the CR-521 drives are hard-wired to drive ID 0. The drives have to use different drive IDs, and each drive has to get a unique minor number (0...3), corresponding indirectly to its drive ID. The drive IDs may be selected freely from 0 to 3 - they do not have to be in consecutive order. As Don Carroll, don@ds9.us.dell.com or FIDO 1:382/14, told me, it is possible to change old drives to any ID, too. He writes in this sense: "In order to be able to use more than one single speed drive (they do not have the ID jumpers) you must add a DIP switch and two resistors. The pads are already on the board next to the power connector. You will see the silkscreen for the switch if you remove the top cover. 1 2 3 4 ID 0 = x F F x O = "on" ID 1 = x O F x F = "off" ID 2 = x F O x x = "don't care" ID 3 = x O O x Next to the switch are the positions for R76 (7k) and R78 (12k). I had to play around with the resistor values - ID 3 did not work with other values. If the values are not good, ID 3 behaves like ID 0." To use more than 4 drives, you simply need a second controller card at a different address and a second cable. The driver supports reading of data from the CD and playing of audio tracks. The audio part should run with WorkMan, xcdplayer, with the "non-X11" products CDplayer and WorkBone - tell me if it is not compatible with other software. With the CR-562 and CR-563 drives, the reading of audio frames is possible. This is implemented by an IOCTL function which reads READ_AUDIO frames of 2352 bytes at once (configurable with the "READ_AUDIO" define, default is 0). Reading the same frame a second time gives different data; the frame data start at a different position, but all read bytes are valid, and we always read 98 consecutive chunks (of 24 Bytes) as a frame. Reading more than 1 frame at once possibly misses some chunks at each frame boundary. This lack has to get corrected by external, "higher level" software which reads the same frame again and tries to find and eliminate overlapping chunks (24-byte-pieces). The transfer rate with reading audio (1-frame-pieces) currently is very slow. This can be better reading bigger chunks, but the "missing" chunks possibly occur at the beginning of each single frame. The software interface possibly may change a bit the day the SCSI driver supports it too. With all but the CR-52x drives, MultiSession is supported. Photo CDs work (the "old" drives like CR-521 can access only the first session of a photoCD). At ftp.gwdg.de:/pub/linux/hpcdtoppm/ you will find Hadmut Danisch's package to convert photo CD image files and Gerd Knorr's viewing utility. The transfer rate will reach 150 kB/sec with "old" drives, 300 kB/sec with double-speed drives, and about 500 kB/sec with quad speed drives. XA (PhotoCD) disks with "old" drives give only 50 kB/sec. This release is part of the standard kernel and consists of - this README file - the driver file linux/drivers/block/sbpcd.c - the header file linux/include/linux/sbpcd.h. To install: ----------- 1. Setup your hardware parameters. Though the driver does "auto-probing" at a lot of (not all possible!) addresses, this step is recommended for every-day use. a. Go into /usr/src/linux/include/linux/sbpcd.h and configure it for your hardware (near the beginning): a1. Set it up for the appropriate type of interface board. "Original" CreativeLabs sound cards need "SBPRO 1". Most "compatible" sound cards (for example "Highscreen", "SoundFX" and "Galaxy") need "SBPRO 0". The "no-sound" board from OmniCd needs the "SBPRO 1" setup. All other "no-sound" boards need the "SBPRO 0" setup. The Spea Media FX sound card needs "SBPRO 2". sbpcd.c holds some examples in its auto-probe list. If you configure "SBPRO" wrong, the playing of audio CDs will work, but you will not be able to mount a data CD. a2. Tell the address of your CDROM_PORT (not of the sound port). a3. Set DISTRIBUTION to 0. b. Additionally for 2.a1 and 2.a2, the setup may be done during boot time (via the "kernel command line" or "LILO option"): sbpcd=0x230,SoundBlaster or sbpcd=0x320,LaserMate or sbpcd=0x330,SPEA This is especially useful if you install a fresh distribution. 2. "cd /usr/src/linux" and do a "make config" and select "y" for Matsushita CD-ROM support and for ISO9660 FileSystem support. If you do not have a second, third, or fourth controller installed, do not say "y" to the secondary Matsushita CD-ROM questions. SCSI and/or SCSI CD-ROM support is not needed. 3. Then do a "make dep", then make the kernel image ("make zlilo" or else). 4. Make the device file(s). The driver uses definitely and exclusive the MAJOR 25, so do mknod /dev/sbpcd b 25 0 (if you have only one drive) and/or mknod /dev/sbpcd0 b 25 0 mknod /dev/sbpcd1 b 25 1 mknod /dev/sbpcd2 b 25 2 mknod /dev/sbpcd3 b 25 3 to make the node(s). The driver no longer uses the "AT bus style" device numbering; the SCSI scheme is used now; that means, the "first found" drive gets MINOR 0 (regardless to its jumpered ID), the "next found" (at the same cable) gets MINOR 1, ... For a second interface board, you have to make nodes like mknod /dev/sbpcd4 b 26 0 mknod /dev/sbpcd5 b 26 1 and so on. Use the MAJORs 26, 27, 28. If you further make a link like ln -s sbpcd /dev/cdrom you can use the name /dev/cdrom, too. 5. Reboot with the new kernel. You should now be able to do mkdir /CD and mount -t iso9660 -o ro /dev/sbpcd /CD or mount -t iso9660 -o ro,block=2048 /dev/sbpcd /CD and see the contents of your CD in the /CD directory, and/or hear music with "workman -c /dev/sbpcd &". Using sbpcd as a "loadable module": ----------------------------------- If you do NOT select "Matsushita/Panasonic CDROM driver support" during the "make config" of your kernel, you can build the "loadable module" sbpcd.o. Read /usr/src/linux/README.modules on this. If sbpcd gets used as a module, the support of more than one interface card (i.e. drives 4...15) is disabled. You can specify interface address and type with the "insmod" command like: # insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x340,0 or # insmod /usr/src/linux/modules/sbpcd.o sbpcd=0x230,1 where the last number represents the SBPRO setting (no strings allowed here). Things of interest: ------------------- The driver is configured to try the LaserMate type of interface at I/O port 0x0340 first. If this is not appropriate, sbpcd.h should get changed (you will find the right place - just at the beginning). No DMA and no IRQ is used. To reduce or increase the amount of kernel messages, edit sbpcd.c and play with the "DBG_xxx" switches (initialization of the variable "sbpcd_debug"). The driver uses the "variable BLOCK_SIZE" feature. To use it, you have to specify "block=2048" as a mount option. Doing this will disable the direct execution of a binary from the CD; you have to copy it to a device with the standard BLOCK_SIZE (1024) before. So, do not use this if your system is directly "running from the CDROM" (like some of YGGDRASIL's installation variants). There are CDs on the market (like the german "unifix" Linux distribution) which MUST get handled with a block_size of 1024. Generally, one can say all the CDs which hold files of the name YMTRANS.TBL are defective; do not use block=2048 with those. At the beginning of sbpcd.c, you will find some "#define"s (f.e. EJECT and JUKEBOX). With that, you can configure the driver for some special things. You can use the appended program "cdtester" to set the auto-eject feature during runtime. Jeff Tranter's "eject" utility can do this, too (and more) for you. There is a new ioctl CDROMMULTISESSION to obtain with a user program if the CD is an XA disk and - if it is - where the last session starts. The "cdtester" program illustrates how to call it. Auto-probing at boot time: -------------------------- The driver does auto-probing at many well-known interface card addresses, but not all: Some probings can cause a hang if an NE2000 ethernet card gets touched, because SBPCD's auto-probing happens before the initialization of the net drivers. Those "hazardous" addresses are excluded from auto-probing; the "kernel command line" feature has to be used during installation if you have your drive at those addresses. The "module" version is allowed to probe at those addresses, too. The auto-probing looks first at the configured address resp. the address submitted by the kernel command line. With this, it is possible to use this driver within installation boot floppies, and for any non-standard address, too. Auto-probing will make an assumption about the interface type ("SBPRO" or not), based upon the address. That assumption may be wrong (initialization will be o.k., but you will get I/O errors during mount). In that case, use the "kernel command line" feature and specify address & type at boot time to find out the right setup. For every-day use, address and type should get configured within sbpcd.h. That will stop the auto-probing due to success with the first try. The kernel command "sbpcd=0" suppresses each auto-probing and causes the driver not to find any drive; it is meant for people who love sbpcd so much that they do not want to miss it, even if they miss the drives. ;-) If you configure "#define CDROM_PORT 0" in sbpcd.h, the auto-probing is initially disabled and needs an explicit kernel command to get activated. Once activated, it does not stop before success or end-of-list. This may be useful within "universal" CDROM installation boot floppies (but using the loadable module would be better because it allows an "extended" auto-probing without fearing NE2000 cards). To shorten the auto-probing list to a single entry, set DISTRIBUTION 0 within sbpcd.h. Setting up address and interface type: -------------------------------------- If your I/O port address is not 0x340, you have to look for the #defines near the beginning of sbpcd.h and configure them: set SBPRO to 0 or 1 or 2, and change CDROM_PORT to the address of your CDROM I/O port. Most of the "SoundBlaster compatible" cards behave like the no-sound interfaces! With "original" SB Pro cards, an initial setting of CD_volume through the sound cards MIXER register gets done. If you are using a "compatible" sound card of types "LaserMate" or "SPEA", you can set SOUND_BASE (in sbpcd.h) to get it done with your card, too... Using audio CDs: ---------------- Workman, WorkBone, xcdplayer, cdplayer and the nice little tool "cdplay" (see README.aztcd from the Aztech driver package) should work. The program CDplayer likes to talk to "/dev/mcd" only, xcdplayer wants "/dev/rsr0", workman loves "/dev/sr0" or "/dev/cdrom" - so, do the appropriate links for using them without the need of supplying parameters. Copying audio tracks: --------------------- The following program will copy track 1 (or a piece of it) from an audio CD into the file "track01": /*=================== begin program ========================================*/ /* * read an audio track from a CD * * (c) 1994 Eberhard Moenkeberg * may be used & enhanced freely * * Due to non-existent sync bytes at the beginning of each audio frame (or due * to a firmware bug within all known drives?), it is currently a kind of * fortune if two consecutive frames fit together. * Usually, they overlap, or a little piece is missing. This happens in units * of 24-byte chunks. It has to get fixed by higher-level software (reading * until an overlap occurs, and then eliminate the overlapping chunks). * ftp.gwdg.de:/pub/linux/misc/cdda2wav-sbpcd.*.tar.gz holds an example of * such an algorithm. * This example program further is missing to obtain the SubChannel data * which belong to each frame. * * This is only an example of the low-level access routine. The read data are * pure 16-bit CDDA values; they have to get converted to make sound out of * them. * It is no fun to listen to it without prior overlap/underlap correction! */ #include #include #include static struct cdrom_tochdr hdr; static struct cdrom_tocentry entry[101]; static struct cdrom_read_audio arg; static u_char buffer[CD_FRAMESIZE_RAW]; static int datafile, drive; static int i, j, limit, track, err; static char filename[32]; main(int argc, char *argv[]) { /* * open /dev/cdrom */ drive=open("/dev/cdrom", 0); if (drive<0) { fprintf(stderr, "can't open drive.\n"); exit (-1); } /* * get TocHeader */ fprintf(stdout, "getting TocHeader...\n"); err=ioctl(drive, CDROMREADTOCHDR, &hdr); if (err!=0) { fprintf(stderr, "can't get TocHeader (error %d).\n", err); exit (-1); } else fprintf(stdout, "TocHeader: %d %d\n", hdr.cdth_trk0, hdr.cdth_trk1); /* * get and display all TocEntries */ fprintf(stdout, "getting TocEntries...\n"); for (i=1;i<=hdr.cdth_trk1+1;i++) { if (i!=hdr.cdth_trk1+1) entry[i].cdte_track = i; else entry[i].cdte_track = CDROM_LEADOUT; entry[i].cdte_format = CDROM_LBA; err=ioctl(drive, CDROMREADTOCENTRY, &entry[i]); if (err!=0) { fprintf(stderr, "can't get TocEntry #%d (error %d).\n", i, err); exit (-1); } else { fprintf(stdout, "TocEntry #%d: %1X %1X %06X %02X\n", entry[i].cdte_track, entry[i].cdte_adr, entry[i].cdte_ctrl, entry[i].cdte_addr.lba, entry[i].cdte_datamode); } } fprintf(stdout, "got all TocEntries.\n"); /* * ask for track number (not implemented here) */ track=1; #if 0 /* just read a little piece (4 seconds) */ entry[track+1].cdte_addr.lba=entry[track].cdte_addr.lba+300; #endif /* * read track into file */ sprintf(filename, "track%02d\0", track); datafile=creat(filename, 0755); if (datafile<0) { fprintf(stderr, "can't open datafile %s.\n", filename); exit (-1); } arg.addr.lba=entry[track].cdte_addr.lba; arg.addr_format=CDROM_LBA; /* CDROM_MSF would be possible here, too. */ arg.nframes=1; arg.buf=&buffer[0]; limit=entry[track+1].cdte_addr.lba; for (;arg.addr.lba * published under the GPL * * made under heavy use of the "Tiny Audio CD Player" * from Werner Zimmermann * (see linux/drivers/block/README.aztcd) */ #undef AZT_PRIVATE_IOCTLS /* not supported by every CDROM driver */ #define SBP_PRIVATE_IOCTLS /* not supported by every CDROM driver */ #include #include #include #include #include #ifdef AZT_PRIVATE_IOCTLS #include #endif AZT_PRIVATE_IOCTLS #ifdef SBP_PRIVATE_IOCTLS #include #include #endif SBP_PRIVATE_IOCTLS struct cdrom_tochdr hdr; struct cdrom_tochdr tocHdr; struct cdrom_tocentry TocEntry[101]; struct cdrom_tocentry entry; struct cdrom_multisession ms_info; struct cdrom_read_audio read_audio; struct cdrom_ti ti; struct cdrom_subchnl subchnl; struct cdrom_msf msf; struct cdrom_volctrl volctrl; #ifdef AZT_PRIVATE_IOCTLS union { struct cdrom_msf msf; unsigned char buf[CD_FRAMESIZE_RAW]; } azt; #endif AZT_PRIVATE_IOCTLS int i, i1, i2, i3, j, k; unsigned char sequence=0; unsigned char command[80]; unsigned char first=1, last=1; char *default_device="/dev/cdrom"; char dev[20]; char filename[20]; int drive; int datafile; int rc; void help(void) { printf("Available Commands:\n"); printf("STOP s EJECT e QUIT q\n"); printf("PLAY TRACK t PAUSE p RESUME r\n"); printf("NEXT TRACK n REPEAT LAST l HELP h\n"); printf("SUBCHANNEL_Q c TRACK INFO i PLAY AT a\n"); printf("READ d READ RAW w READ AUDIO A\n"); printf("MS-INFO M TOC T START S\n"); printf("SET EJECTSW X DEVICE D DEBUG Y\n"); printf("AUDIO_BUFSIZ Z RESET R BLKRASET B\n"); printf("SET VOLUME v GET VOLUME V\n"); } /* * convert MSF number (3 bytes only) to Logical_Block_Address */ int msf2lba(u_char *msf) { int i; i=(msf[0] * CD_SECS + msf[1]) * CD_FRAMES + msf[2] - CD_BLOCK_OFFSET; if (i<0) return (0); return (i); } /* * convert logical_block_address to m-s-f_number (3 bytes only) */ void lba2msf(int lba, unsigned char *msf) { lba += CD_BLOCK_OFFSET; msf[0] = lba / (CD_SECS*CD_FRAMES); lba %= CD_SECS*CD_FRAMES; msf[1] = lba / CD_FRAMES; msf[2] = lba % CD_FRAMES; } int init_drive(char *dev) { unsigned char msf_ent[3]; /* * open the device */ drive=open(dev,0); if (drive<0) return (-1); /* * get TocHeader */ printf("getting TocHeader...\n"); rc=ioctl(drive,CDROMREADTOCHDR,&hdr); if (rc!=0) { printf("can't get TocHeader (error %d).\n",rc); return (-2); } else first=hdr.cdth_trk0; last=hdr.cdth_trk1; printf("TocHeader: %d %d\n",hdr.cdth_trk0,hdr.cdth_trk1); /* * get and display all TocEntries */ printf("getting TocEntries...\n"); for (i=1;i<=hdr.cdth_trk1+1;i++) { if (i!=hdr.cdth_trk1+1) TocEntry[i].cdte_track = i; else TocEntry[i].cdte_track = CDROM_LEADOUT; TocEntry[i].cdte_format = CDROM_LBA; rc=ioctl(drive,CDROMREADTOCENTRY,&TocEntry[i]); if (rc!=0) { printf("can't get TocEntry #%d (error %d).\n",i,rc); } else { lba2msf(TocEntry[i].cdte_addr.lba,&msf_ent[0]); if (TocEntry[i].cdte_track==CDROM_LEADOUT) { printf("TocEntry #%02X: %1X %1X %02d:%02d:%02d (lba: 0x%06X) %02X\n", TocEntry[i].cdte_track, TocEntry[i].cdte_adr, TocEntry[i].cdte_ctrl, msf_ent[0], msf_ent[1], msf_ent[2], TocEntry[i].cdte_addr.lba, TocEntry[i].cdte_datamode); } else { printf("TocEntry #%02d: %1X %1X %02d:%02d:%02d (lba: 0x%06X) %02X\n", TocEntry[i].cdte_track, TocEntry[i].cdte_adr, TocEntry[i].cdte_ctrl, msf_ent[0], msf_ent[1], msf_ent[2], TocEntry[i].cdte_addr.lba, TocEntry[i].cdte_datamode); } } } return (hdr.cdth_trk1); /* number of tracks */ } void display(int size,unsigned char *buffer) { k=0; getchar(); for (i=0;i<(size+1)/16;i++) { printf("%4d:",i*16); for (j=0;j<16;j++) { printf(" %02X",buffer[i*16+j]); } printf(" "); for (j=0;j<16;j++) { if (isalnum(buffer[i*16+j])) printf("%c",buffer[i*16+j]); else printf("."); } printf("\n"); k++; if (k>=20) { printf("press ENTER to continue\n"); getchar(); k=0; } } } main(int argc, char *argv[]) { printf("\nTesting tool for a CDROM driver's audio functions V0.1\n"); printf("(C) 1995 Eberhard Moenkeberg \n"); printf("initializing...\n"); rc=init_drive(default_device); if (rc<0) printf("could not open %s (rc=%d).\n",default_device,rc); help(); while (1) { printf("Give a one-letter command (h = help): "); scanf("%s",command); command[1]=0; switch (command[0]) { case 'D': printf("device name (f.e. /dev/sbpcd3): ? "); scanf("%s",&dev); close(drive); rc=init_drive(dev); if (rc<0) printf("could not open %s (rc %d).\n",dev,rc); break; case 'e': rc=ioctl(drive,CDROMEJECT); if (rc<0) printf("CDROMEJECT: rc=%d.\n",rc); break; case 'p': rc=ioctl(drive,CDROMPAUSE); if (rc<0) printf("CDROMPAUSE: rc=%d.\n",rc); break; case 'r': rc=ioctl(drive,CDROMRESUME); if (rc<0) printf("CDROMRESUME: rc=%d.\n",rc); break; case 's': rc=ioctl(drive,CDROMSTOP); if (rc<0) printf("CDROMSTOP: rc=%d.\n",rc); break; case 'S': rc=ioctl(drive,CDROMSTART); if (rc<0) printf("CDROMSTART: rc=%d.\n",rc); break; case 't': rc=ioctl(drive,CDROMREADTOCHDR,&tocHdr); if (rc<0) { printf("CDROMREADTOCHDR: rc=%d.\n",rc); break; } first=tocHdr.cdth_trk0; last= tocHdr.cdth_trk1; if ((first==0)||(first>last)) { printf ("--got invalid TOC data.\n"); } else { printf("--enter track number(first=%d, last=%d): ",first,last); scanf("%d",&i1); ti.cdti_trk0=i1; if (ti.cdti_trk0last) ti.cdti_trk0=last; ti.cdti_ind0=0; ti.cdti_trk1=last; ti.cdti_ind1=0; rc=ioctl(drive,CDROMSTOP); rc=ioctl(drive,CDROMPLAYTRKIND,&ti); if (rc<0) printf("CDROMPLAYTRKIND: rc=%d.\n",rc); } break; case 'n': rc=ioctl(drive,CDROMSTOP); if (++ti.cdti_trk0>last) ti.cdti_trk0=last; ti.cdti_ind0=0; ti.cdti_trk1=last; ti.cdti_ind1=0; rc=ioctl(drive,CDROMPLAYTRKIND,&ti); if (rc<0) printf("CDROMPLAYTRKIND: rc=%d.\n",rc); break; case 'l': rc=ioctl(drive,CDROMSTOP); if (--ti.cdti_trk0last) entry.cdte_track=last; entry.cdte_format=CDROM_MSF; rc=ioctl(drive,CDROMREADTOCENTRY,&entry); if (rc<0) printf("CDROMREADTOCENTRY: rc=%d.\n",rc); else { printf("Mode %d Track, starts at %02d:%02d:%02d\n", entry.cdte_adr, entry.cdte_addr.msf.minute, entry.cdte_addr.msf.second, entry.cdte_addr.msf.frame); } break; case 'a': printf("Address (min:sec:frm) "); scanf("%d:%d:%d",&i1,&i2,&i3); msf.cdmsf_min0=i1; msf.cdmsf_sec0=i2; msf.cdmsf_frame0=i3; if (msf.cdmsf_sec0>59) msf.cdmsf_sec0=59; if (msf.cdmsf_frame0>74) msf.cdmsf_frame0=74; lba2msf(TocEntry[last+1].cdte_addr.lba-1,&msf.cdmsf_min1); rc=ioctl(drive,CDROMSTOP); rc=ioctl(drive,CDROMPLAYMSF,&msf); if (rc<0) printf("CDROMPLAYMSF: rc=%d.\n",rc); break; #ifdef AZT_PRIVATE_IOCTLS /*not supported by every CDROM driver*/ case 'd': printf("Address (min:sec:frm) "); scanf("%d:%d:%d",&i1,&i2,&i3); azt.msf.cdmsf_min0=i1; azt.msf.cdmsf_sec0=i2; azt.msf.cdmsf_frame0=i3; if (azt.msf.cdmsf_sec0>59) azt.msf.cdmsf_sec0=59; if (azt.msf.cdmsf_frame0>74) azt.msf.cdmsf_frame0=74; rc=ioctl(drive,CDROMREADMODE1,&azt.msf); if (rc<0) printf("CDROMREADMODE1: rc=%d.\n",rc); else display(CD_FRAMESIZE,azt.buf); break; case 'w': printf("Address (min:sec:frame) "); scanf("%d:%d:%d",&i1,&i2,&i3); azt.msf.cdmsf_min0=i1; azt.msf.cdmsf_sec0=i2; azt.msf.cdmsf_frame0=i3; if (azt.msf.cdmsf_sec0>59) azt.msf.cdmsf_sec0=59; if (azt.msf.cdmsf_frame0>74) azt.msf.cdmsf_frame0=74; rc=ioctl(drive,CDROMREADMODE2,&azt.msf); if (rc<0) printf("CDROMREADMODE2: rc=%d.\n",rc); else display(CD_FRAMESIZE_RAW,azt.buf); /* currently only 2336 */ break; #endif case 'v': printf("--Channel 0 (Left) (0-255): "); scanf("%d",&i1); volctrl.channel0=i1; printf("--Channel 1 (Right) (0-255): "); scanf("%d",&i1); volctrl.channel1=i1; volctrl.channel2=0; volctrl.channel3=0; rc=ioctl(drive,CDROMVOLCTRL,&volctrl); if (rc<0) printf("CDROMVOLCTRL: rc=%d.\n",rc); break; case 'q': close(drive); exit(0); case 'h': help(); break; case 'T': /* display TOC entry - without involving the driver */ scanf("%d",&i); if ((ihdr.cdth_trk1)) printf("invalid track number.\n"); else printf("TocEntry %02d: adr=%01X ctrl=%01X msf=%02d:%02d:%02d mode=%02X\n", TocEntry[i].cdte_track, TocEntry[i].cdte_adr, TocEntry[i].cdte_ctrl, TocEntry[i].cdte_addr.msf.minute, TocEntry[i].cdte_addr.msf.second, TocEntry[i].cdte_addr.msf.frame, TocEntry[i].cdte_datamode); break; case 'A': /* read audio data into file */ printf("Address (min:sec:frm) ? "); scanf("%d:%d:%d",&i1,&i2,&i3); read_audio.addr.msf.minute=i1; read_audio.addr.msf.second=i2; read_audio.addr.msf.frame=i3; read_audio.addr_format=CDROM_MSF; printf("# of frames ? "); scanf("%d",&i1); read_audio.nframes=i1; k=read_audio.nframes*CD_FRAMESIZE_RAW; read_audio.buf=malloc(k); if (read_audio.buf==NULL) { printf("can't malloc %d bytes.\n",k); break; } sprintf(filename,"audio_%02d%02d%02d_%02d.%02d\0", read_audio.addr.msf.minute, read_audio.addr.msf.second, read_audio.addr.msf.frame, read_audio.nframes, ++sequence); datafile=creat(filename, 0755); if (datafile<0) { printf("can't open datafile %s.\n",filename); break; } rc=ioctl(drive,CDROMREADAUDIO,&read_audio); if (rc!=0) { printf("CDROMREADAUDIO: rc=%d.\n",rc); } else { rc=write(datafile,&read_audio.buf,k); if (rc!=k) printf("datafile I/O error (%d).\n",rc); } close(datafile); break; case 'X': /* set EJECT_SW (0: disable, 1: enable auto-ejecting) */ scanf("%d",&i); rc=ioctl(drive,CDROMEJECT_SW,i); if (rc!=0) printf("CDROMEJECT_SW: rc=%d.\n",rc); else printf("EJECT_SW set to %d\n",i); break; case 'M': /* get the multisession redirection info */ ms_info.addr_format=CDROM_LBA; rc=ioctl(drive,CDROMMULTISESSION,&ms_info); if (rc!=0) { printf("CDROMMULTISESSION(lba): rc=%d.\n",rc); } else { if (ms_info.xa_flag) printf("MultiSession offset (lba): %d (0x%06X)\n",ms_info.addr.lba,ms_info.addr.lba); else { printf("this CD is not an XA disk.\n"); break; } } ms_info.addr_format=CDROM_MSF; rc=ioctl(drive,CDROMMULTISESSION,&ms_info); if (rc!=0) { printf("CDROMMULTISESSION(msf): rc=%d.\n",rc); } else { if (ms_info.xa_flag) printf("MultiSession offset (msf): %02d:%02d:%02d (0x%02X%02X%02X)\n", ms_info.addr.msf.minute, ms_info.addr.msf.second, ms_info.addr.msf.frame, ms_info.addr.msf.minute, ms_info.addr.msf.second, ms_info.addr.msf.frame); else printf("this CD is not an XA disk.\n"); } break; #ifdef SBP_PRIVATE_IOCTLS case 'Y': /* set the driver's message level */ #if 0 /* not implemented yet */ printf("enter switch name (f.e. DBG_CMD): "); scanf("%s",&dbg_switch); j=get_dbg_num(dbg_switch); #else printf("enter DDIOCSDBG switch number: "); scanf("%d",&j); #endif printf("enter 0 for \"off\", 1 for \"on\": "); scanf("%d",&i); if (i==0) j|=0x80; printf("calling \"ioctl(drive,DDIOCSDBG,%d)\"\n",j); rc=ioctl(drive,DDIOCSDBG,j); printf("DDIOCSDBG: rc=%d.\n",rc); break; case 'Z': /* set the audio buffer size */ printf("# frames wanted: ? "); scanf("%d",&j); rc=ioctl(drive,CDROMAUDIOBUFSIZ,j); printf("%d frames granted.\n",rc); break; case 'V': rc=ioctl(drive,CDROMVOLREAD,&volctrl); if (rc<0) printf("CDROMVOLCTRL: rc=%d.\n",rc); printf("Volume: channel 0 (left) %d, channel 1 (right) %d\n",volctrl.channel0,volctrl.channel1); break; case 'R': rc=ioctl(drive,CDROMRESET); if (rc<0) printf("CDROMRESET: rc=%d.\n",rc); break; case 'B': /* set the driver's (?) read ahead value */ printf("enter read-ahead size: ? "); scanf("%d",&i); rc=ioctl(drive,BLKRASET,i); if (rc<0) printf("BLKRASET: rc=%d.\n",rc); break; #endif SBP_PRIVATE_IOCTLS default: printf("unknown command: \"%s\".\n",command); break; } } } /*==========================================================================*/ /* * Overrides for Emacs so that we follow Linus's tabbing style. * Emacs will notice this stuff at the end of the file and automatically * adjust the settings for this buffer only. This must remain at the end * of the file. * --------------------------------------------------------------------------- * Local variables: * c-indent-level: 8 * c-brace-imaginary-offset: 0 * c-brace-offset: -8 * c-argdecl-indent: 8 * c-label-offset: -8 * c-continued-statement-offset: 8 * c-continued-brace-offset: 0 * End: */